Products

Seven Star THG-1000 Watt Step Up / Down Voltage Converter TransformerThis voltage converter can be used in 110 volt countries and 220 volt countries. It will convert from 220-240 volt to 110-120 volt AND from 110-120 volt to 220-240 volt. 1000 watts capacity, converts 110 to 220 volt or 220 to 110 volt, for continuous use, 1 Outlet, Fuse Protection, CE Mark1000 watts capacity on THG-1000Grounded Transformer for Two Way Voltage Conversion - 110 volt to 220 volt and 220 volts to 110 voltBuilt-in fuse protection systemCan be used continuously with its 80% capacityOperates on 110/120 or 220/240 volt AC and converts to and from 110/120/220/230/240 voltInput voltage selector switch (120 or 220 volt)Ideal for both electric and electronic products like Computers, Consumer Electronics, Appliances and Testing Equipments1 OutletBuilt-in Euro/Asian power cord with 2 prong Schuko Grounded plugSupplied with 2 prong plug adapter for American outletOptional Plug Adapters required (For UK, Australia, Ireland, Italy, South Africa)CE MarkCarrying handle for portability

Seven Star THG-1500 Watt Step Up / Down Voltage Converter TransformerThis voltage converter can be used in 110 volt countries and 220 volt countries. It will convert from 220-240 volt to 110-120 volt AND from 110-120 volt to 220-240 volt. 1500 watts capacity, converts 110 to 220 volt or 220 to 110 volt, for continuous use, 1 Outlet, Fuse Protection, CE Mark1500 watts capacity on THG-1500Grounded Transformer for Two Way Voltage Conversion - 110 volt to 220 volt and 220 volts to 110 voltBuilt-in fuse protection systemCan be used continuously with its 80% capacityOperates on 110/120 or 220/240 volt AC and converts to and from 110/120/220/230/240 voltInput voltage selector switch (120 or 220 volt)Ideal for both electric and electronic products like Computers, Consumer Electronics, Appliances and Testing Equipments1 OutletBuilt-in Euro/Asian power cord with 2 prong Schuko Grounded plugSupplied with 2 prong plug adapter for American outletOptional Plug Adapters required (For UK, Australia, Ireland, Italy, South Africa)CE MarkCarrying handle for portability

Seven Star THG-2000 Watt Step Up / Down Voltage Converter TransformerThis voltage converter can be used in 110 volt countries and 220 volt countries. It will convert from 220-240 volt to 110-120 volt AND from 110-120 volt to 220-240 volt. 2000 watts capacity, converts 110 to 220 volt or 220 to 110 volt, for continuous use, 1 Outlet, Fuse Protection, CE Mark2000 watts capacity on THG-2000Grounded Transformer for Two Way Voltage Conversion - 110 volt to 220 volt and 220 volts to 110 voltBuilt-in fuse protection systemCan be used continuously with its 80% capacityOperates on 110/120 or 220/240 volt AC and converts to and from 110/120/220/230/240 voltInput voltage selector switch (120 or 220 volt)Ideal for both electric and electronic products like Computers, Consumer Electronics, Appliances and Testing Equipments1 OutletBuilt-in Euro/Asian power cord with 2 prong Schuko Grounded plugSupplied with 2 prong plug adapter for American outletOptional Plug Adapters required (For UK, Australia, Ireland, Italy, South Africa)CE MarkCarrying handle for portability

Seven Star THG-3000 Watt Step Up / Down Voltage Converter TransformerThis voltage converter can be used in 110 volt countries and 220 volt countries. It will convert from 220-240 volt to 110-120 volt AND from 110-120 volt to 220-240 volt. 3000 watts capacity, converts 110 to 220 volt or 220 to 110 volt, for continuous use, 1 Outlet, Fuse Protection, CE Mark3000 watts capacity on THG-3000Grounded Transformer for Two Way Voltage Conversion - 110 volt to 220 volt and 220 volts to 110 voltBuilt-in fuse protection systemCan be used continuously with its 80% capacityOperates on 110/120 or 220/240 volt AC and converts to and from 110/120/220/230/240 voltInput voltage selector switch (120 or 220 volt)Ideal for both electric and electronic products like Computers, Consumer Electronics, Appliances and Testing Equipments1 OutletBuilt-in Euro/Asian power cord with 2 prong Schuko Grounded plugSupplied with 2 prong plug adapter for American outletOptional Plug Adapters required (For UK, Australia, Ireland, Italy, South Africa)CE MarkCarrying handle for portability

Seven Star THG-500 Watt Step Up / Down Voltage Converter TransformerThis voltage converter can be used in 110 volt countries and 220 volt countries. It will convert from 220-240 volt to 110-120 volt AND from 110-120 volt to 220-240 volt. 500 watts capacity, converts 110 to 220 volt or 220 to 110 volt, for continuous use, 1 Outlet, Fuse Protection, CE Mark500 watts capacity on THG-500Grounded Transformer for Two Way Voltage Conversion - 110 volt to 220 volt and 220 volts to 110 voltBuilt-in fuse protection systemCan be used continuously with its 80% capacityOperates on 110/120 or 220/240 volt AC and converts to and from 110/120/220/230/240 voltInput voltage selector switch (120 or 220 volt)Ideal for both electric and electronic products like Computers, Consumer Electronics, Appliances and Testing Equipments1 OutletBuilt-in Euro/Asian power cord with 2 prong Schuko Grounded plugSupplied with 2 prong plug adapter for American outletOptional Plug Adapters required (For UK, Australia, Ireland, Italy, South Africa)CE MarkCarrying handle for portabilitySeven Star THG-500 Watt Step Up / Down Voltage Converter TransformerThis voltage converter can be used in 110 volt countries and 220 volt countries. It will convert from 220-240 volt to 110-120 volt AND from 110-120 volt to 220-240 volt. 500 watts capacity, converts 110 to 220 volt or 220 to 110 volt, for continuous use, 1 Outlet, Fuse Protection, CE Mark500 watts capacity on THG-500Grounded Transformer for Two Way Voltage Conversion - 110 volt to 220 volt and 220 volts to 110 voltBuilt-in fuse protection systemCan be used continuously with its 80% capacityOperates on 110/120 or 220/240 volt AC and converts to and from 110/120/220/230/240 voltInput voltage selector switch (120 or 220 volt)Ideal for both electric and electronic products like Computers, Consumer Electronics, Appliances and Testing Equipments1 OutletBuilt-in Euro/Asian power cord with 2 prong Schuko Grounded plugSupplied with 2 prong plug adapter for American outletOptional Plug Adapters required (For UK, Australia, Ireland, Italy, South Africa)CE MarkCarrying handle for portability

Seven Star THG-5000 Watt Step Up / Down Voltage Converter Transformer This voltage converter can be used in 110 volt countries and 220 volt countries. It will convert from 220-240 volt to 110-120 volt AND from 110-120 volt to 220-240 volt. 5000 watts capacity, converts 110 to 220 volt or 220 to 110 volt, for continuous use, 1 Outlet, Fuse Protection, CE Mark 5000 watts capacity on THG-5000 Grounded Transformer for Two Way Voltage Conversion - 110 volt to 220 volt and 220 volts to 110 volt Built-in fuse protection system Can be used continuously with its 80% capacity Operates on 110/120 or 220/240 volt AC and converts to and from 110/120/220/230/240 volt Input voltage selector switch (120 or 220 volt) Ideal for both electric and electronic products like Computers, Consumer Electronics, Appliances and Testing Equipments 1 Outlet Built-in Euro/Asian power cord with 2 prong Schuko Grounded plug Supplied with 2 prong plug adapter for American outlet Optional Plug Adapters required (For UK, Australia, Ireland, Italy, South Africa) CE Mark Carrying handle for portability

Seven Star THG-750 Watt Step Up / Down Voltage Converter TransformerThis voltage converter can be used in 110 volt countries and 220 volt countries. It will convert from 220-240 volt to 110-120 volt AND from 110-120 volt to 220-240 volt. 750 watts capacity, converts 110 to 220 volt or 220 to 110 volt, for continuous use, 1 Outlet, Fuse Protection, CE Mark750 watts capacity on THG-750Grounded Transformer for Two Way Voltage Conversion - 110 volt to 220 volt and 220 volts to 110 voltBuilt-in fuse protection systemCan be used continuously with its 80% capacityOperates on 110/120 or 220/240 volt AC and converts to and from 110/120/220/230/240 voltInput voltage selector switch (120 or 220 volt)Ideal for both electric and electronic products like Computers, Consumer Electronics, Appliances and Testing Equipments1 OutletBuilt-in Euro/Asian power cord with 2 prong Schuko Grounded plugSupplied with 2 prong plug adapter for American outletOptional Plug Adapters required (For UK, Australia, Ireland, Italy, South Africa)CE MarkCarrying handle for portability

Tmvel Universal International Power Adapter Plug Tip Converter - Convert Europe, EU/UK/CN/AU To USA - Great for Cell Phone Charger - Not Converter Type A is used, for instance, in North and Central America and Japan. This class II ungrounded plug with two flat parallel prongs is pretty much standard in most of North and Central America. It is known as NEMA 1-15 and was invented in 1904 by Harvey Hubbell II. The plug has two flat 1.5 mm thick blades, measuring 15.9 – 18.3 mm in length and spaced 12.7 mm apart. Type A plugs are generally polarised and can only be inserted one way because the two blades do not have the same width. The blade connected to neutral is 7.9 mm wide and the hot blade is 6.3 mm wide. This plug is rated at 15 A. Type A and B plugs have two flat prongs with a hole near the tip. These holes aren’t there without a reason. If you were to take apart a type A or B socket and look at the contact wipers that the prongs slide into, you would find that in some cases they have have bumps on them. These bumps fit into the holes so that the outlet can grip the plug’s prongs more firmly. This prevents the plug from slipping out of the socket due to the weight of the plug and cord. It also improves the contact between the plug and the outlet. Some sockets, however, do not have those bumps but just two spring-action blades that grip the sides of the plug pin, in which case the holes are not necessary. There are also some special outlets which allow you to lock the cord into the socket, by putting rods through the holes. In this way, vending machines and the like cannot be unplugged. Moreover, electrical devices can be factory-sealed by the manufacturer using a plastic tie or a small padlock through one or both of the plug prong holes. For example, a manufacturer might apply a plastic band through the hole and attach it to a tag that says: “You must do X or Y before plugging in this device”. The user cannot plug in the device without removing the tag, so the user is sure to see the tag. Type A and B plugs are not insulated (i.e. the pin shanks do not have a black covering towards the plug body like type C, G, I, L or N plugs) and the outlets are not recessed into the wall, which means that if a the plug is pulled halfway out, its prongs are still connected to the socket. Type A and B sockets are potentially dangerous, since the distance between the receptacle and a partially pulled-out plug is big enough to touch the pins with your fingers or with a metal object such as a teaspoon. This product is a passive device and does not convert voltage. Any item plugged in must already be compatible with the voltage being supplied by the socket. Rated: 10A/250V Insulated Voltage-Proof: 3 KV Materials Shell: ABS (UL-94HB) Plug Plate: ABS (UL-94VO) Safety Certification: CE Marking

U.S. Proof Service, Free USB Bulk Packaging, Free Continental U.S. Ground Shipping, Free Setup Fee: $150 Tmvel Universal International Power Adapter Plug Tip Converter - Convert Europe, EU/UK/CN/AU To USA - Great for Cell Phone Charger - Not Converter Type A is used, for instance, in North and Central America and Japan. This class II ungrounded plug with two flat parallel prongs is pretty much standard in most of North and Central America. It is known as NEMA 1-15 and was invented in 1904 by Harvey Hubbell II. The plug has two flat 1.5 mm thick blades, measuring 15.9 – 18.3 mm in length and spaced 12.7 mm apart. Type A plugs are generally polarised and can only be inserted one way because the two blades do not have the same width. The blade connected to neutral is 7.9 mm wide and the hot blade is 6.3 mm wide. This plug is rated at 15 A. Type A and B plugs have two flat prongs with a hole near the tip. These holes aren’t there without a reason. If you were to take apart a type A or B socket and look at the contact wipers that the prongs slide into, you would find that in some cases they have have bumps on them. These bumps fit into the holes so that the outlet can grip the plug’s prongs more firmly. This prevents the plug from slipping out of the socket due to the weight of the plug and cord. It also improves the contact between the plug and the outlet. Some sockets, however, do not have those bumps but just two spring-action blades that grip the sides of the plug pin, in which case the holes are not necessary. There are also some special outlets which allow you to lock the cord into the socket, by putting rods through the holes. In this way, vending machines and the like cannot be unplugged. Moreover, electrical devices can be factory-sealed by the manufacturer using a plastic tie or a small padlock through one or both of the plug prong holes. For example, a manufacturer might apply a plastic band through the hole and attach it to a tag that says: “You must do X or Y before plugging in this device”. The user cannot plug in the device without removing the tag, so the user is sure to see the tag. Type A and B plugs are not insulated (i.e. the pin shanks do not have a black covering towards the plug body like type C, G, I, L or N plugs) and the outlets are not recessed into the wall, which means that if a the plug is pulled halfway out, its prongs are still connected to the socket. Type A and B sockets are potentially dangerous, since the distance between the receptacle and a partially pulled-out plug is big enough to touch the pins with your fingers or with a metal object such as a teaspoon. This product is a passive device and does not convert voltage. Any item plugged in must already be compatible with the voltage being supplied by the socket. Rated: 10A/250V Insulated Voltage-Proof: 3 KV Materials Shell: ABS (UL-94HB) Plug Plate: ABS (UL-94VO) Safety Certification: CE Marking

Type I Universal Grounded Plug Adapter With The Patented Universal Receptacle Design That Accepts Plugs From Most Countries Including The US And Canada. The 'Type I' Plug Adapter Is Grounded And Fits In To Outlets In Countries Such As China, Australia, New Zealand And More. Visit Our Worldwide Plug Adapter Guide For More Info On Outlets In Specific Countries. The 2-In-1 Adapter Plug Features Additional Convenient Receptacle For Ungrounded 2 Prong Plugs On Top. Other Countries Include: Argentina, Australia, China (Mainland, Excluding Taiwan), Fiji, New Zealand, Papua New Guinea, Tokelau (The Union Islands), Uruguay Engineered for global travel Designed with double ports (receptacles) allow you to plug-in two electrical devices (connectors) at once (Does not Convert Voltage) US Patented Universal Input: Accepts plugs from all countries (except the Type M - big S. Africa 8.7mm Plug) Output: "Type I" Suitable for Australia & New Zealand New conductivity design - internal metal interfaces provides better conductivity. Grounded 3 Round Prong plug. Max Capacity Up to 3000 Watt (max 250 Volt, 15 A)  

Type A is used, for instance, in North and Central America and Japan. This class II ungrounded plug with two flat parallel prongs is pretty much standard in most of North and Central America. It is known as NEMA 1-15 and was invented in 1904 by Harvey Hubbell II. The plug has two flat 1.5 mm thick blades, measuring 15.9 – 18.3 mm in length and spaced 12.7 mm apart. Type A plugs are generally polarised and can only be inserted one way because the two blades do not have the same width. The blade connected to neutral is 7.9 mm wide and the hot blade is 6.3 mm wide. This plug is rated at 15 A. Type A and B plugs have two flat prongs with a hole near the tip. These holes aren’t there without a reason. If you were to take apart a type A or B socket and look at the contact wipers that the prongs slide into, you would find that in some cases they have have bumps on them. These bumps fit into the holes so that the outlet can grip the plug’s prongs more firmly. This prevents the plug from slipping out of the socket due to the weight of the plug and cord. It also improves the contact between the plug and the outlet. Some sockets, however, do not have those bumps but just two spring-action blades that grip the sides of the plug pin, in which case the holes are not necessary. There are also some special outlets which allow you to lock the cord into the socket, by putting rods through the holes. In this way, vending machines and the like cannot be unplugged. Moreover, electrical devices can be factory-sealed by the manufacturer using a plastic tie or a small padlock through one or both of the plug prong holes. For example, a manufacturer might apply a plastic band through the hole and attach it to a tag that says: “You must do X or Y before plugging in this device”. The user cannot plug in the device without removing the tag, so the user is sure to see the tag. Type A and B plugs are not insulated (i.e. the pin shanks do not have a black covering towards the plug body like type C, G, I, L or N plugs) and the outlets are not recessed into the wall, which means that if a the plug is pulled halfway out, its prongs are still connected to the socket. Type A and B sockets are potentially dangerous, since the distance between the receptacle and a partially pulled-out plug is big enough to touch the pins with your fingers or with a metal object such as a teaspoon. This product is a passive device and does not convert voltage. Any item plugged in must already be compatible with the voltage being supplied by the socket. Rated: 10A/250V Insulated Voltage-Proof: 3 KV Materials Shell: ABS (UL-94HB) Plug Plate: ABS (UL-94VO) Safety Certification: CE Marking